Usage
  • 28 views
  • 114 downloads

Development of Prediction Tools for Improved Wear Assessment of Pipelines and Complex Geometries

  • Author / Creator
    Adedeji, Oluwaseun Ezekiel
  • Particle-laden flows such as pneumatic conveying or slurry transport are common in the minerals processing and oil sands industries. These industries face the challenge of erosion wear due to the repeated impact of the entrained particles, and subsequent damage to pipelines and equipment. Many economic losses such as equipment replacement cost, start-up and shutdown cost, and loss in production are associated with this erosion wear. An estimated $1 billion/year in losses has been reported for the Canadian oil sands industry alone. It is, therefore, important for industries to know when and where failure will occur, as well as how much material is lost in order to take proactive steps to reduce these losses. The goal of this thesis is to develop more accurate predictive tools and methodologies that industries can use to assess the wear performance of their processes. Bench-scale devices and wear models are the typical predictive tools which will be explored in this thesis. Part I of this thesis focuses on the development of a bench-scale device known as the toroid wear tester (TWT) as a slurry pipeline wear prediction tool. An initial Computational Fluid Dynamics (CFD) analysis and flow visualization experiments were conducted to study the hydrodynamics in the TWT. The results revealed regions of strong secondary flows in the TWT, and further identified possible operating conditions for wear testing which may be scalable to horizontal slurry pipelines applications. A subsequent experimental investigation studied how the bed of particles respond to the TWT hydrodynamics. Coulombic stress was correlated to measured wear rate in the device over a range of operating conditions. It was found that a fully settled slurry flow regime occurs in the TWT when the ratio of the linear wheel speed to the particle terminal settling velocity is less than 7, and that there is a linear correlation between the measured wear rate and Coulombic stress in this region. However, to apply this correlation to slurry pipelines, the amount of wear due to Coulombic stress in pipelines must also be calculated. A CFD and experimental data analysis were therefore conducted on slurry pipeline wear data as a follow-up study. The results revealed that a correlation similar to that obtained for the TWT also exists in slurry pipelines between Coulombic stress and the associated wear rate. More slurry pipeline wear data are needed to further develop and support the correlation that would allow the use of the TWT for the prediction of wear in slurry pipelines. Part II of this thesis presents studies on the improvement of wear model performance in complex geometries, and for effective decision-making in industrial process operations. The first study used CFD modelling to develop a geometry correction factor function (GCFF) for a standard 90-degree elbow. The GCFF provides factors that correct the effect of geometry-induced secondary flows not originally accounted for in the development of traditional single particle erosion models. The GCFF in this study was combined with the Oka erosion model and it performed better than the model alone. Another CFD analysis was conducted on a Once-Through Steam Generator (OTSG) system used in in situ oil sands extraction. Superheated steam transports precipitated fine particles (10 microns) at very low concentration (3 ppm) in the OTSG boiler tubes. Contrary to previous assumptions, the investigation showed severe erosion wear damage in the boiler tubes due to these fine particles. Additional analysis showed that the API RP 14E industrial guideline used in the design of OTSGs cannot adequately capture the effect of operational changes such as an increase in steam production rate. The CFD analysis performed was, however, able to show that a 10% increase in OTSG operating velocity would cause failure in the OTSG boilers two times faster. In summary, a significant step towards accurate wear prediction in slurry pipelines and other particle-handling systems was made though the research presented.

  • Subjects / Keywords
  • Graduation date
    Spring 2021
  • Type of Item
    Thesis
  • Degree
    Doctor of Philosophy
  • DOI
    https://doi.org/10.7939/r3-sr0x-nk29
  • License
    This thesis is made available by the University of Alberta Libraries with permission of the copyright owner solely for non-commercial purposes. This thesis, or any portion thereof, may not otherwise be copied or reproduced without the written consent of the copyright owner, except to the extent permitted by Canadian copyright law.